show repository <repository name> | i <repository name>
acs restore <backup name> repository <repository name>
show application status acs

source

user@host:~$ sudo aptitude install linux-headers-$(uname -r)

1. umount /boot/efi
2. apt install -f
3. mount -a
4. apt update && sudo apt upgrade

source

configure network ipv4 manual <ip address> <subnet mask> <df gateway> management0
show network

Use CLI and enter: get hardware nic port <name> or diag hardware deviceinfo nic <name>

Start -> RUN -> osk

You’ll get on screen keyboard and now you can press CTRL + ALT + DEL to change your password.

user@computer:~$ dmesg | grep tty
[ 0.088345] printk: console [tty0] enabled
[ 0.418156] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 5.030307] usb 1-3.1.3: pl2303 converter now attached to ttyUSB0
[86188.149229] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[86271.641530] usb 1-2: pl2303 converter now attached to ttyUSB0
[86796.881771] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[86855.323347] usb 1-4: pl2303 converter now attached to ttyUSB0
[86877.932139] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[86884.784432] usb 1-4: pl2303 converter now attached to ttyUSB0
[87068.706927] pl2303 ttyUSB0: pl2303_set_control_lines – failed: -19
[87068.706937] pl2303 ttyUSB0: error sending break = -19
[87068.707250] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[259915.126314] cdc_acm 1-3.1.3:1.0: ttyACM0: USB ACM device

I upgraded ubuntu to focal 20.04 and SSH was unable to negotiate with network devices I tried to ssh on.
Solution was found here, or simpy editing /etc/ssh/ssh_conf by adding following lines to the end of the file:

Ciphers aes128-ctr,aes192-ctr,aes256-ctr,aes128-cbc,3des-cbc
MACs hmac-md5,hmac-sha1,umac-64@openssh.com
KexAlgorithms diffie-hellman-group1-sha1,curve25519-sha256@libssh.org,ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group14-sha1
HostKeyAlgorithms ssh-rsa,ssh-dss

I had some problems while downgrading so here are my steps.

Documentation is not really clear about this, so here are the steps.

1. from fxos, reformat system
   firepower-2110# connect local-mgmt
   firepower-2110(local-mgmt)# format everything
   All configuration and bootable images will be lost.
   Do you still want to format? (yes/no):yes
2. enter rommon and boot via tftp
   rommon 1 > address 10.86.118.4
   rommon 2 > netmask 255.255.250.0
   rommon 3 > server 10.86.118.21
   rommon 4 > gateway 10.86.118.1
   rommon 5 > file cisco-asa-fp2k.9.8.2.SPA
   rommon 6 > set
   rommon 7 > sync
   rommon 8 > tftp -b
3. everything is erased so you have to reconfigure your mgmt interface
   firepower-2110# scope fabric-interconnect a
   firepower /fabric-interconnect* # set out-of-band static ip 10.86.118.4 netmask 255.255.250.0 gw 10.86.118.21
   firepower /fabric-interconnect* # commit-buffer
4. download image (could not get USB to mount so I used ftp)
   firepower # scope firmware
   firepower /firmware # download image ftp://user@10.86.118.21/cisco-asa-fp2k.9.8.2.SPA
   check status:
   firepower /firmware # show download-task
5. install image
   look at version you want to install:
   firepower /firmware # show package
   firepower /firmware # scope auto-install
   firepower /firmware/auto-install # install security-pack version
   check status (wait for Update Software Pack Completed):
   firepower /firmware # show
6. configure ftd/initial configuration
   firepower /firmware # connect ftd

Try “pager“